Remington Staple Gun Side By Side Cocking Hammer Shotgun User Guide

Owners  
Manual  
Owner’s Manual for:  
Remington Model SPR 220H  
Side-By-Side Cocking Hammer  
Shotgun  
PAGE 2 ........THE TEN COMMANDMENTS OF FIREARM SAFETY  
PAGE 7 ........IMPORTANT PARTS OF THE FIREARM  
PAGE 10........ASSEMBLY INSTRUCTIONS  
PAGE 11........LOADING AND UNLOADING  
PAGE 14 ......FIRING  
IMPORTANT!  
READ ALL WARNINGS AND  
INSTRUCTIONS IN THIS  
MANUAL BEFORE USING THIS SHOTGUN  
 
PAGE 16 ......DISASSEMBLY INSTRUCTIONS  
3r d C OMMA NDM ENT  
Never Rely on Your Firearm’s Safety Mechanism to Justify Careless Handling.  
If your firearm is equipped with a manual safety mechanism, do not rely on the safety as an excuse for improp-  
er or careless handling of the firearm. The safety mechanism is merely a supplement to your proper handling of  
the firearm. The safety mechanism may be broken or altered. Even if you think you have previously engaged  
the safety in the “safe” position, it may have been inadvertently disengaged without your knowledge while being  
carried. Never assume that the safety mechanism is engaged in the “safe” position. Your assumption may be  
wrong or mistaken. Treat your firearms safety mechanism like you would treat any other mechanical device - as  
something that could break or fail.  
Not all safety mechanisms operate in the same manner. Before using any firearm, know and understand pre-  
cisely how the safety mechanism on that particular firearm operates. Never pull the trigger when the safety  
mechanism is in the “safe” position, and keep your fingers away from the trigger while loading, unloading, and  
engaging or disengaging the safety mechanism.  
4 t h C O MMAN DM ENT  
Know Your Target and What’s Beyond It.  
Never fire a shot unless you know exactly where the shot is going and what it will strike. Bullets and shot can  
travel great distances with deadly velocity. When hunting game, never fire at a sound, a movement or a patch of  
color - an impulsive shot can have tragic consequences. A fellow hunter in camouflage may be mistaken for  
game by an impulsive shooter.  
In addition to being sure of your target, you must know what lies beyond the target. In other words, make sure  
of your backstop. Also, beware of ricochets - never shoot at water or a hard surface.  
5 t h C O MMAN DM ENT  
Use Proper Ammunition.  
Every firearm is designed to use only a specified caliber, gauge or length of ammunition. Use of the wrong  
ammunition can cause serious personal injury or death. It is your responsibility to make sure the ammunition  
exactly matches the specifications for your firearm.  
Use of improperly reloaded ammunition can also be dangerous. Firearms are designed, manufactured, and  
proof-tested to specified industry standards. Hand-loaded or reloaded ammunition that deviates, either inten-  
tionally or accidentally, from specified loadings can be extremely hazardous. It is strongly recommended, there-  
fore, that you use only factory ammunition from a reputable ammunition manufacturer. If you do reload, you  
have assumed the risks and responsibilities of an ammunition manufacturer.  
6 t h C O MMAN DM ENT  
If Your Firearm Fails to Fire When You Pull the Trigger, Handle With Care.  
If a chambered round of ammunition does not fire when you pull the trigger, stop and keep the muzzle pointed  
in a safe direction. Treat your firearm as if it could still discharge. Keep your face away from the breech. Slowly  
and carefully open the action, return the safety mechanism to the “safe” position, and unload the cartridge from  
the chamber. Dispose of the cartridge safely. If your firearm repeatedly fails to fire when you pull the trigger, take  
your firearm and ammunition to a competent gunsmith or return the firearm to the manufacturer for inspection.  
3
 
7t h COMMA NDM EN T  
Always Wear Eye and Ear Protection.  
Wear protective shooting glasses and hearing protection when shooting. Be sure to wear eye protection when  
disassembling or cleaning a firearm to protect your eyes from springs and other tensioned parts. Continued  
exposure to shooting noise can permanently damage your hearing.  
8t h CO MM AN DM EN T  
Be Sure the Barrel is Clear of Obstructions Before Shooting.  
With your firearm completely unloaded, open the action and make sure there are no obstructions or debris in the  
barrel. Even a small obstruction such as snow or mud in the barrel can cause the barrel or receiver to burst when  
the next round is fired. Use a cleaning rod to remove obstructions and residues from the barrel. If the firing  
noise or recoil seems weak, stop and completely unload your firearm to check for obstructions before firing  
another shot. NEVER try to shoot out an obstruction by loading and firing another round of ammunition.  
9t h CO MM AN DM EN T  
Never Alter or Modify Your Firearm and Have it Cleaned and Serviced Regularly.  
Your firearm has been carefully designed and manufactured to operate according to certain factory specifications.  
NEVER alter or modify your firearm, especially its trigger or safety mechanism, in any way. Such alterations or  
modifications can adversely affect the safe operation of your firearm, endangering you and those around you.  
As with any mechanical device, the parts of a firearm are subject to wear or breakage. To assure optimum safe-  
ty and performance, your firearm must be maintained and serviced on a regular basis. Only a competent gun-  
smith or a Remington Authorized Service Center should service or repair your firearm.  
Proper cleaning and lubrication are also important to maintain the safe and proper functioning of your firearm.  
Follow the cleaning and lubrication instructions set forth in the owner’s manual for your firearm. NEVER attempt  
to clean or lubricate a loaded firearm.  
10 th CO MM AND ME N T  
Learn How Your Firearm Operates.  
Not all firearms are alike. Before you use any firearm for the first time, you must become totally familiar with  
how that firearm operates. When you receive a new firearm, read and understand the owner’s manual before  
assembling the firearm for the first time. If you acquire a used firearm, request an owner’s manual and have the  
rifle inspected by a competent gunsmith to determine whether it is in good working order. If you do not have an  
owner’s manual, contact the manufacturer to obtain one. If you are selling or trading your firearm to someone  
else, be sure to transfer the owner’s manual to the new owner.  
LEAD EXPOSURE WARNING  
Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in expo-  
sure to lead, a substance known to cause birth defects, reproductive harm, cancer and other serious physical  
injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.  
SHOOT SOBER!  
Guns and alcohol or drugs don’t mix. Never consume anything that would even mildly impair your judgement or  
physical coordination while handling a firearm.  
WARNING  
Failure to follow any of these safety rules may cause personal injury or death to the shooter or bystander and  
damage to property. Do not use a firearm until you fully understand and practice the Ten Commandments of  
Firearm Safety. If you have any questions about the safe use of a Remington firearm, write to us at Remington  
Arms Company, Inc., Consumer Service, P.O. Box 700, Madison, NC 27025-0700, or call us at 1-800-243-9700.  
4
 
Use the Security Lock Provided with your Shotgun  
This shotgun comes with a security lock to assist in protecting against unauthorized use. (See Picture 1A).  
The shotgun must be unloaded when the security lock is in place on the shotgun. WARNING: Using the  
security lock cannot substitute for securing your firearm and ammunition in separate, locked locations.  
Picture 1A  
The security lock operates as follows:  
1. To open the Trigger Lock put the Key into the notches of the Trigger Lock Nut and un-screw it  
counter-clockwise (See Pictures 1 and 2). Remove the Trigger Lock Screw.  
Picture 1  
Picture 2  
2. To install the Trigger Lock on a side-by-side shotgun put the Trigger Lock over the trigger guard with the  
larger end of the Trigger Lock shroud pointing toward the muzzle. Then place the Trigger Lock Screw  
through the cross-slotted hole on the side of the Trigger Lock shroud. (See Picture 3).  
Picture 3  
Download from Www.Somanuals.com5. All Manuals Search And Download.  
Use the Security Lock Provided with your Shotgun (cont’d)  
3. Screw the Trigger Lock Nut on the Trigger Lock Screw (clockwise) and tighten the nut with the key.  
DO NOT TIGHTEN THE NUT TOO TIGHT OR YOU COULD DAMAGE THE LOCK SCREW  
(See Picture 4).  
Picture 4  
4. To remove the Trigger Lock, unscrew the Trigger Lock nut with the key and detach the Trigger Lock Screw  
(See Picture 5)  
Picture 5  
WARNING  
Always store the key to the security lock: (1) in a separate location away from the shotgun; (2) in a secure location unknown and not  
accessible to others, especially children. Whether you secure your firearms by using the supplied security lock, a gun lock or a safe or some  
other mechanism, it is YOUR RESPONSIBILITY to store your firearms in such a manner that children and other unauthorized persons cannot  
gain access to them.  
6
 
Important Parts of the Firearm  
Congratulations on your choice of a Remington® Model 220H Side-By-Side Cocking Hammer shotgun. With  
proper care and if used in accordance with the Ten Commandments of Firearm’s Safety and this owner’s manual,  
your shotgun should give you many years of dependable use and enjoyment. The following picture depicts the  
main parts of your shotgun and will aid in understanding the instructions in this Owner’s Manual.  
SAFETY MECHANISM  
STOCK  
MUZZLE  
BARREL  
FORE END  
RECEIVER  
TRIGGERS  
TRIGGER GUARD  
This picture shows the main parts of a Remington Model SPR220H shotgun. The picture will aid in understanding the instructions in this book.  
External Control Parts  
Trigger Block Safety: The safety mechanism of the shotgun provides protection against accidental and  
unintentional discharge under normal usage when properly engaged and in good working order. The safety  
mechanism is not a substitute for the rules of safe gun handling. Do not disengage the safety unless you are ready  
to fire the shotgun. MAKE SURE YOU UNDERSTAND HOW THE SAFETY WORKS BEFORE YOU LOAD  
OR USE THE SHOTGUN.  
The safety mechanism is a tang-style located behind the top lever. (See Picture 6). To place the safety in the “on”  
or “safe” position, pull the button all the way to the rear. When in the “on” or “safe” position, the safety blocks the  
rearward motion of the trigger(s). To place the safety in the “off” or “fire” position, push the slide all the way to the  
forward. When in the “off” or “fire” position, a red dot is exposed behind the slide button. You have now  
disengaged the safety and the shotgun is in the ready-to-fire position, (see Picture 7).  
Picture 6  
Picture 7  
WARNING  
Do not touch the trigger(s) while moving the safety. When operating the safety button, make sure you push or pull it to the full extent of its travel  
in the desired direction, either fully “on” or fully “off.” Half-safe or partially safe is UNSAFE.  
WARNING  
The Shotgun is designed to and WILL FIRE when the trigger is pulled and the safety mechanism is in the “off” or “fire” position.  
7
 
External Control Parts (cont’d)  
Top Lever: The top lever is located just forward of the safety mechanism. (See Picture 8). The top lever is used  
to break open the action to load and/or unload the shotgun, and to assemble and disassemble the shotgun. To break  
open the action, fully push the top lever to the right. (See Picture 9). The safety will engage when the top lever is  
pushed to the right when opening the barrels  
Picture 8  
Picture 9  
WARNING  
When operating the top lever, you must: 1) make sure the safety mechanism is in the “on” or “safe” position; (2) keep your fingers away from the  
trigger(s) and outside of the trigger guard; and (3) control the direction of the muzzle of the shotgun.  
Trigger(s): Model SPR 220H Shotguns are available in a double-trigger configuration.  
WARNING  
Never pull the trigger(s) until you are actually ready to fire. Keep your fingers off the trigger(s) and outside of the trigger guard until you are ready  
to pull the trigger and fire the shotgun. When opening and closing the action and when engaging or disengaging the safety mechanism, make sure  
your fingers are outside the trigger guard and away from the trigger(s).  
Model SPR 220H shotguns are patterned after classic side-by-side shotguns with two triggers. The front trigger  
always fires the right barrel. The back trigger always fires the left barrel. Pulling either trigger with the safety in the  
“off” or “fire” position fires the shotgun. (See Picture 10).  
Picture 10  
WARNING  
Never fire a double-trigger shotgun by using the two fingers because you may inadvertently pull both triggers at the same time resulting in a near  
simultaneous firing of both barrels. Use your index finger to pull one of the triggers to fire the first shot. After that shot is fired, release the  
trigger and move your index finger to the other trigger to fire the second shot.  
8
 
External Control Parts (cont’d)  
Extractors: Model SPR 220H shotguns  
are equipped with extractors from the  
factory for extraction of the fired rounds  
upon opening of the action. (See Picture 11).  
Picture 11  
The Fore End: The forend is the wooden grip piece  
that attaches to the barrel assembly and locks the barrel  
assembly into the receiver. (See Picture 12).  
The fore end has a mechanical latch which is used to  
lock and unlock the fore end to the barrel assembly.  
Never attempt to fire your shotgun without having  
the fore end locked in its proper position on the  
barrel assembly.  
Picture 12  
External Hammers: The external hammers are  
located on both sides of the receiver. (See Picture 13).  
The hammers must be manually cocked to fire the shotgun.  
Picture 13  
External Firing Pins: The external firing pins are  
located on both sides of the upper receiver in front of  
the hammers (See Picture 14).  
The Serial Number: The shotgun’s serial number is  
located under the top lever.  
Picture 14  
Download from Www.Somanuals.com9. All Manuals Search And Download.  
Instructions For Assembly Of Shotgun  
WARNING  
Before you begin to assemble the shotgun, you MUST (1) look down the barrel from the breech end toward the muzzle end to make sure there  
is no ammunition in the chambers or obstruction in the barrels, and (2) make sure the safety is in the “safe” position.  
Your shotgun was shipped with the barrel assembly (barrel and fore end) detached from the receiver assembly.  
To assemble the shotgun, follow these instructions:  
1. Remove the plastic bags or wrapping covering the parts. Then remove the fore end from the barrel by  
pulling outward on the mechanical lever in the lower mid-section of the fore end and tipping the fore end  
out and away from the barrel. See Picture 15. (See Picture 15).  
Picture 15  
2. Now push the top lever of the receiver to the right and hold with one hand. Do not force the top lever.  
(See Picture 16).  
Picture 16  
3. Holding the barrels with the other hand, engage the lower locking lug located on the lower portion of the  
barrel with the receiver. The half round cut out on the lower locking lug fits around the round bar in the  
forward lower portion of the slot in the receiver. With the barrels engaged into the receiver, swing the  
barrels up into the locked position. The top lever should move back to the center once the barrels are  
locked into position. Note: The top lever may not move completely to the center on a new shotgun until  
the gun is broken in. The top lever must move at least three quarters of its full travel distance.  
(See Pictures 17A, 17B, 17C and 17D).  
10  
 
Instructions For Assembly Of Shotgun (cont’d)  
Picture 17A  
Picture 17B  
Picture 17C  
Picture 17D  
4. Now that the barrels have been locked into the receiver,  
you must reattach the fore end to the barrels. Pull  
outward on the mechanical latch in the center of the  
fore end and place the fore end on the receiver. With  
an upward swinging motion, lock the fore end onto  
the barrels. Do not force the fore end into its locked  
position on the barrels. If the latch does not go to  
its final flat position, it may be necessary to push  
it into place. Never force the latch in the flat position.  
(See Picture 18).  
Picture 18  
Loading and Unloading Your Shotgun  
WARNING  
Never load or fire the shotgun unless the barrels is locked into position on the receiver, and the fore end is locked in to the receiver and barrels.  
WARNING  
Make sure the shotgun is pointed in a safe direction and the trigger block safety is engaged at all times while loading and unloading.  
NEVER allow your fingers or other objects to contact the trigger (s) while loading or unloading.  
WARNING  
Do not disengage the trigger block safety until you are ready to fire and have the gun pointed safely downrange  
WARNING: DO NOT LOAD SHOTGUN UNTIL YOU ARE READY TO FIRE.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Loading and Unloading Your Shotgun (cont’d)  
TO LOAD:  
1. Make sure the ammunition that you are using is the correct size and gauge. The barrels are marked with  
3
the gauge and chamber size. Barrels marked 3” (76mm) will use only 2 /4” (70mm) or 3”(76mm) shot  
shells and must not be used with 3 1/2” (89mm) shells. Barrels marked with 2 3/4” (70mm) will use only  
2 3/4” (70mm) and must not be used with or 3” (76mm) or 3 1/2” (89mm) shells.  
2. Visually inspect the chambers and barrels for obstructions by breaking open the shotgun by depressing  
the locking lever and tipping the barrels down. The chambers and barrels should be free of oil or grease  
or obstructions. (See Picture 19).  
Picture 19  
3. After inspection, load the correct type of shot shells into the chambers making sure that the shells are  
flush with the extractor (See Pictures 20 and 21), then close the action by swinging the barrels up until  
they lock into the receiver and the top lever moves back to the center position. If the top lever does not  
move to the center, break open the action again and check to see if the shot shells are fully seated in the  
chambers. If the shells are fully seated then re-close the action. If the shot shells are not fully seated,  
check the chamber for blockage and check the shells for deformation and retry closing the action once  
more. If the shells are the correct type and the chambers are not blocked and the shells are not deformed  
and the top lever does not move at least three quarters of the full travel distance to the center after  
closing, then unload the gun (follow Unloading Instructions) and have a competent gunsmith look at the  
shotgun or return the gun to Remington I.S.P. (See address in Parts & Service Section) for  
inspection. Note: The top lever may not move completely to the center on a new shotgun until the gun is  
broken in. The lever must move at least three quarters of the full travel distance. Try and move the top  
lever to the center position by pushing it, do not force it.  
Picture 20  
Picture 21  
12  
 
Loading and Unloading Your Shotgun (cont’d)  
TO UNLOAD:  
1. Break open the shotgun by use of the top lever, and tip the barrels down.  
2. Remove the shell(s) from the chamber(s) by grabbing them by the rim of the shell(s) and pulling them  
from the chambers and store them in a safe place.  
3. Visually check the barrels to make sure that they are free from obstructions. (See Picture 22).  
4. Engage the trigger block safety after the shotgun is unloaded.  
Picture 22  
Cocking and Uncocking Your Shotgun  
TO COCK:  
1. While keeping your fingers away from the triggers, grab the shotgun firmly with your right  
hand around the stock’s pistol grip. Place your right thumb on the top of the right hammer.  
(See Pictures 23A and 23B).  
2. Pull the hammer rearward until it locks in the cocked position. (See Picture 23C).  
Picture 23A  
Picture 23B  
Picture 2#C  
3. Next, place your right thumb on the left hammer and pull  
it rearward until it locks in the cocked position.  
(See Picture 24).  
4. Keeping your shotgun pointed in a safe direction, or at  
your intended target, remove the safety and pull the trigger  
of the barrel you want to shoot first.  
Picture 24  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
Cocking and Uncocking Your Shotgun (cont’d)  
TO UNCOCK:  
1. While holding the shotgun firmly by the stock’s pistol grip, break open the shotgun by using the top lever.  
Remove any live rounds (see Unloading Procedures). (See Pictures 25A and 25B). Repeat this step  
with the other trigger.  
2. With the shotgun broken open and properly unloaded, disengage the safety. (See Picture 25C).  
Picture 25A  
Picture 25B  
Picture 25C  
3. Place your thumb on the top of the right hammer. Holding the hammer firmly, pull the front trigger and  
slowly lower the hammer to its resting position. Repeat this step with the left hammer.  
(See Pictures 26A and 26B).  
Picture 26A  
Picture 26B  
Firing Your Shotgun  
WARNING: NEVER LOAD A CARTRIDGE INTO THE CHAMBER UNTIL YOU ARE READY TO FIRE THE SHOTGUN.  
WARNING  
Do not disengage the trigger block safety until the shotgun is pointed in a safe direction and you are ready to fire.  
WARNING  
If a cartridge does not fire and the trigger has been pulled and the trigger block safety is disengaged…Stop! And do the following: a) Make sure  
the gun is pointed in a safe direction b) Engage the trigger block safety c) Wait 60 seconds d) Follow the instructions above for unloading the  
shotgun.  
WARNING  
If during firing the sound of any cartridge is noticeably softer or louder than the previous cartridge fired, Stop! Do not load another cartridge or  
fire another cartridge and do the following: a) Make sure the gun is pointed in a safe direction b) Engage the trigger block safety c) Follow the  
instructions above for unloading the shotgun d) With the shotgun unloaded visually inspect the shotgun for barrel blockage or damage.  
Then inspect the mechanical operation and receiver of the shotgun for damage before continuing.  
READ, UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE FIRING THE SHOTGUN.  
14  
 
Firing Your Shotgun (cont’d)  
TO FIRE THE SHOTGUN:  
1. Make sure the shotgun is pointed in a safe direction with the trigger block safety engaged.  
(See Picture 27).  
2. Make sure you are wearing eye and ear protection.  
3. Keep your fingers away from the trigger(s).  
Picture 27  
4. Cock hammers per Cocking Instructions.  
5. Push the trigger block safety to the “off” or “fire” position with the red dot showing. (See Picture 28).  
6. With the butt stock held firmly again your shoulder and the barrels pointed towards your intended target,  
place your trigger finger on the trigger. The shotgun will fire when you pull or squeeze the trigger with  
the requisite force. (See Picture 29).  
Picture 28  
Picture 29  
7. When you are using a double-trigger, move your finger to the other trigger and pull it.  
The second round will now fire.  
WARNING  
Once you have fired the shotgun, immediately push the trigger block safety to the “on” or “safe” position. Then follow the unloading  
instructions above while keeping the muzzle pointed in a safe direction.  
WARNING  
Never carry the shotgun with the hammers cocked. If you have cocked the hammer(s) but then not fired the gun, you must uncock the hammers.  
Because their is now a live round(s) in the chamber(s), EXTREME CAUTION must be employed when uncocking the hammer. Make sure the  
shotgun is pointed in a safe direction throughout the uncocking process.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
Instructions For Disassembly Of The Shotgun  
1. Make sure the shotgun is unloaded (FOLLOW UNLOADING INSTRUCTIONS) and pointed in a safe  
direction.  
2. Make sure the trigger block safety is engaged in the “on” or “safe” position. (See Picture 30).  
Picture 30  
3. Remove the fore end from the barrel by pulling out the mechanical lever in the lower center of the fore end  
and removing the fore end in a downward outward swinging motion. (See Picture 31). Never force the  
fore end off the barrel and receiver.  
Picture 31  
4. With the barrels and receiver supported with one hand, push the top lever fully to the right and tip the  
barrels down until they disengage from the receiver. Check the barrels for damage and obstructions after  
removal. (See Pictures 32A and 32B).  
Picture 32A  
Picture 32B  
16  
 
Manufacturer’s Warning  
This firearm was manufactured to properly perform with the original parts as designed. It is your duty to make  
sure any parts you buy are correctly installed and that neither replacements nor originals are altered or changed.  
Your shotgun has many parts that must relate correctly to other parts for safe and accurate operation. Putting a  
gun together wrong or with modified parts can result in a damaged gun, or personal injury or death to you or  
others. Always let a qualified gunsmith work on your gun or at least, check any work not performed  
by a gunsmith. Firearms safety is your primary concern. THE GUN OWNER MUST ACCEPT FULL  
RESPONSIBILITY FOR THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM AFTER  
ANY DISASSEMBLY OR REPLACEMENT OF PARTS.  
To Clean and Maintain Your Shotgun  
A. Follow procedures for unloading shotgun as described previously.  
B. Follow procedures for disassembly of shotgun as described previously.  
C. Materials needed to clean this shotgun are: a cleaning rod, cotton bore patches, brass bore brush,  
powder solvent (such as Remington BriteBore ), a small soft brush and good quality gun oil  
®
(such as Rem Oil).  
WARNING  
Lead or lead compounds are known to the State of California to cause cancer, birth defects, reproductive toxicity, and other serious physical  
injury. Those who clean firearms should take protective measures to avoid contact or exposure to such chemicals.  
D. Using the bore brush with powder solvent, scrub the interior of the barrel and chamber to remove any  
powder and lead residue in the bore. Always and lastly, swab the interior of the barrel with a cotton patch  
with gun oil to coat and protect the bore and chambers from rust and corrosion.  
E. Any powder fouling on the firing wall, barrel, etc. can be easily cleaned with a brush and powder solvent.  
F. All external surfaces should be wiped down with a light coat of rust preventative. Avoid using too much  
oil as powder, dust or other foreign material may get trapped in the oil. This could lead to congealed  
deposits which may interfere with the safe and reliable operation of this shotgun.  
G. USE CAUTION while using solvents in gun bore cleaning. Prolonged or excess contact with  
solvents can damage the gun’s bluing and finish. Be sure to wipe away all excess solvent and then  
lubricate with oil.  
H. A gun should be cleaned after firing. In addition, external parts should be wiped with an oiled cloth  
after handling. A light oil is ordinarily all that is necessary in cleaning if the gun has not been fired or fired  
very little. If a gun is used frequently, it must be cleaned after each firing and regularly serviced by a  
professional gunsmith. If the gun has been stored, remove all excess oil and/or grease before firing.  
Always check to be sure that no cleaning patch or other obstruction remains in the bore or chambers  
before firing.  
17  
 
DANGER – Ammunition Warning  
Firearms may be damaged and serious personal injury or death to the shooter or bystanders may result from any  
condition which contributes to the generation of excessive pressure or uncontrolled release of gas within the  
firearm. Such adverse conditions can be caused by bore or chamber obstructions, propellant powder overloads or  
by defective, incorrect or improperly loaded and assembled cartridge components. Even the strongest firearm can  
be blown up as a result of excessive pressure. It is extremely dangerous to use a cartridge whose pressure is  
greater than that developed by cartridges loaded to industry standards.  
Ammunition (Cartridges) Notice  
We specifically disclaim responsibility for any damage, injury or death occurring in connection with or as the  
result of the use of the shotgun with faulty, non-standard, remanufactured, hand loaded or reloaded ammunition  
or with cartridges other than factory cartridges for which the shotgun was originally chambered.  
Lubrication Warning  
Firing a shotgun with oil, grease or any other material even partially obstructing the bore may result in damage to  
the shotgun and personal injury to the shooter and those nearby. Do not spray or apply lubricants directly on  
ammunition. If the powder charge of a cartridge is affected by the lubricant, they may not fully ignite yet the ener-  
gy from the primer and/or powder may still be sufficient to push the projectile or wad into the bore where it may  
become lodged. Firing a subsequent cartridge into the obstructed bore will damage the shotgun and may cause  
personal injury to the shooter and those nearby. Use lubricants properly. You are responsible for the proper care  
and maintenance of your firearm and ammunition.  
PARTS AND SERVICE  
To Order Parts  
ALL PARTS ARE SUBJECT TO A $10.00 CHARGE FOR SHIPPING AND HANDLING. Some parts are restricted and  
may only be installed by returning the shotgun to us. When ordering parts, please state the Model, Gauge, Serial  
Number, and Finish Color. For parts information, call (321) 639-1432.  
Service  
To obtain information about returning your shotgun for service or repairs, call (321) 639-1432.  
One Year Limited Warranty  
This shotgun is warranted to the original retail customer for one year from the date of retail purchase against  
defects in material and workmanship. All parts and labor or replacement at our option are covered. The wood stock  
is not covered by the one year warranty. The warranty on the wood stock is 60 days and is limited to the original  
retail customer and extends 60 days from the date of retail purchase and covers only manufactured and material  
defects.  
Download from Www.Somanuals.co1m8. All Manuals Search And Download.  
PARTS AND SERVICE (cont’d)  
One Year Limited Warranty  
Transportation to and from our repair facilities, government fees, damage caused by failure to perform normal  
maintenance, sales outside the United States, damage caused by use of high velocity, high pressure, reloaded or  
other nonstandard ammunition, or by any unauthorized repair, modification, misuse, abuse or alteration of the  
shotgun is not covered by this Limited Warranty.  
Implied Warranty  
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL  
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  
To the extent any provision of this warranty is prohibited by federal, state, or municipal law, which cannot be pre-  
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights  
which may vary from state to state.  
To obtain warranty service, send your shotgun with proof of retail purchase, freight prepaid to:  
REMINGTON I.S.P.  
c/o USSG  
402 Richard Road  
Rockledge, FL 32955  
NOTICE: It is illegal to ship a firearm with ammunition in the firearm or in the same packaging. Firearms and  
ammunition must be shipped separately. For information about shipping ammunition, call (321) 639-1432.  
Your Owner’s Manual  
Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and  
safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy  
of this manual from Remington upon request.  
Download from Www.Somanuals.co1m9. All Manuals Search And Download.  
Choke Tubes  
WARNING  
Never install or remove choke tubes while the firearm is loaded. Only install or remove choke tubes with the firearm unloaded, the action open  
and the trigger block safely engaged.  
Screw in Chokes Symbols/Markings  
(This is an option – not all Model 100 shotguns have this feature)  
The end of the choke tubes are marked with slashes to identify the choke construction:  
/
- Full  
// - Improved Modified  
/// - Modified  
//// - Improved Cylinder  
CI - Cylinder  
WARNING  
MAKE SURE YOU FULLY TIGHTEN THE CHOKE TUBE.  
Shooting with a loose choke tube can cause damage to your shotgun.  
Additional Information On Screw Choke Tubes:  
A. Only tighten or loosen choke tubes with flat key wrench supplied with shotgun. Note: wrench (and extra  
choke tube or tubes if supplied) are under the cardboard in front of the shotgun receiver in the box.  
B. Never shoot the SPR 220H shotgun with a partially installed choke tube.  
C. Model SPR 220H shotguns are available with fixed choke or screw choke barrels. There are two types of  
screw chokes available: lead shot choke tubes and steel shot choke tubes. When installed, steel shot  
choke tubes protrude approximately 3/4” from the muzzle end of the barrel and the mating lip will be flush  
with the end of the barrel. When installed, lead shot choke tubes fit flush with or slightly below the  
muzzle end of the barrel. If you have lead shot choke tubes and intend to shoot steel shot cartridges or  
slugs, then you must use only the IC or Cylinder tubes. DO NOT fire steel shot or slugs in Modified,  
Improved Modified or Full lead shot choke tubes. If you have steel shot choke tubes, you may fire steel  
shot cartridges through any of those choke tubes. DO NOT fire slugs in Modified, Improved Modified or  
Full lead shot choke tubes or steel shot choke tubes.  
D. Correctly installed choke tubes: Lead shot choke tubes should fit flush or slightly below the muzzle end  
of the barrel. Steel shot choke tubes will protrude out from the barrel about 3/4” and the mating lip will be  
flush with barrel end.  
E. Before using the SPR 220H shotgun make sure that the choke tubes are installed correctly.  
F. Keep choke tubes lubricated and installed. Never fire the gun without a choke tube installed. Handle choke  
tubes carefully since the leading edge is very thin.  
20  
 
Notes on Shot Material and Chokes:  
1. Shells using Bismuth or Tungsten-Matrix shot are subject to the same barrel and choke tube limitations  
as lead shot. Shells using Tungsten-Iron shot or Hevi-Shot are subject to the same barrel and choke tube  
limitations as steel shot.  
2. On fixed choke guns, shells loaded with steel, Tungsten-Iron or Hevi-Shot should be fired only in  
IC or Cylinder barrels. DO NOT fire steel, Tungsten-Iron or Hevi-Shot shells in fixed barrels with  
Modified, Improved Modified or Full choke barrels. Lead, Bismuth and Tungsten-Matrix may be fired in  
all fixed choke barrels.  
3. On fixed choke guns, slugs may be fired in only IC and Cylinder barrels. DO NOT fire slugs in fixed choke  
barrels with Modified, Improved Modified or Full chokes.  
If you would like to buy extra choke tubes (skeet, trap, extra full, etc.) call (321)-639-1432.  
Your Owner’s Manual  
Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and  
safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy of  
this manual from Remington upon request.  
21  
 
PARTS LIST  
Model 210/220 Exploded View  
1. barrel assembly  
2. stock swivel base  
3. extractor pin  
4. woodscrew  
5. extractor  
29. cam pin  
55. safety  
30. sear pin  
56. screw  
31. sear, LH  
57. bush  
32. left hammer base  
33. plug  
58. screw  
59. plate, LH  
6. screw  
34. plug screw  
35. follower  
60. plate, RH  
7. swivel pin  
8. swivel loop  
9. screw  
61. screw  
36. rod assembly, LH  
37. rod assembly, RH  
38. spring  
62. trigger plate  
63. screw  
10. barrel swivel base  
11. front sight  
12. forend  
64. trigger guard  
65. trigger guard screw  
66. trigger, LH  
39. safety pin and button  
40. screw  
13. forend bush  
14. spring  
41. locking lever  
42. right hammer base  
43. hammer, RH  
44. sear, RH  
67. trigger spring  
68. trigger, RH  
15. catch housing  
16. forend catch  
17. pin  
69. pin  
70. hammer bush  
71. firing pin  
45. screw  
18. screw  
46. button  
72. firing pin spring  
73. firing pin bushing, RH  
74. firing pin bushing, LH  
75. firing pin bushing screw  
76. blocking frame  
77. blocking lever  
78. blocking lever spring  
79. connecting rod  
80. shock-absorber  
81. bushing  
19. screw  
47. locking bolt  
48. screw  
20. screw  
21. screw  
49. locking bolt screw  
50. cam stop  
22. washer  
23. butt plate  
24. hinge  
51. crosspiece  
52. locking bolt lever  
53. ball  
25. stock  
26. safety spring  
27. receiver  
28. cam  
54. hammer, LH  
22  
 
W A R N I N G  
Children are attracted to and can operate  
firearms that can cause severe injuries or  
death. Prevent child access by always keeping guns locked  
away and unloaded when not in use. If you keep a loaded  
firearm where a child obtains and improperly uses it, you  
may be fined or sent to prison.  
ADVERTENCIA  
A los ninos los atroen las armaside de fuego y  
los pueden hacer funcionar. Ellos pueden  
causarses lesiones graves y la muerte. Evite que los ninos  
tengon acceso a los armas de fuego guardandolas siempre  
con llave y descargadas cuando no las este utilizando. Si  
usted tiene un arma de fuego cargado en un lugar en que  
un nono tiene acceso a ella y la usa indebidamente.  
Le pueden dar una multa a enviarlo a la carcel.  
REMINGTON I.S.P.  
c/o USSG  
402 Richard Road  
Rockledge, FL 32955  
Manufacturer:  
Izhevsky Mekhanichesky Zavod  
8, Promyshlennaya str.,  
426063 Izhevsk, Russia  
23  
 
Remington is a trademark registered in the United States Patent and Trademark Office by Remington Arms Company, Inc.  
 

Radio Shack Radar Detector Cat No 22 1698 User Guide
Rheem Water Heater RR40 36FV1 User Guide
Ricoh Digital Camera 170543 User Guide
Samsung Camcorder D352i User Guide
Samsung DVD Player DVD F1080W User Guide
Samsung DVD Player HT TX22 User Guide
Samsung DVD Player V6500K User Guide
Samsung Printer ML 3050 User Guide
Sega Video Games 4200 6367 User Guide
Senco Nail Gun A200BN User Guide